Device.h

#include <stdlib.h>
//#if defined(__AVR_ATmega32U4__)
//#pragma message "当前的开发板是 ATmega32U4"
//#define SerialDevice SerialUSB
//#define NUM_LEDS 11
//#define LED_PIN A3
//#define BOARD_VISION 1
//#include "lib/WS2812_FastLed.h"
//#define PN532_SPI_SS 10

#if defined(ARDUINO_SAMD_ZERO)
#define CDC
#pragma message "当前的开发板是 SAMD21 "
//#include "wiring_private.h"
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
#define NUM_LEDS 11
#define LED_PIN 4
#define BOARD_VISION 2
#include "lib/LED/WS2812_NeoPixel.h"
// Uart SerialPN532(&sercom4, A2, A1, SERCOM_RX_PAD_1, UART_TX_PAD_0);
// void SERCOM4_Handler()
// {
//   SerialPN532.IrqHandler();
// }
#define SerialNFC Serial1
//please install FlashStorage library

#elif defined(ESP8266)
#pragma message "当前的开发板是 ESP8266"
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
#define NUM_LEDS 11
//#define LED_PIN D5 //NodeMCU 1.0(ESP12E-Mod)
#define LED_PIN 14 //Generic ESP8266 Module
#define BOARD_VISION 3
#include "lib/LED/WS2812_FastLed.h"
#include "SoftwareSerial.h"
SoftwareSerial SoftSerialNFC(4, 5); // RX, TX

#elif defined(CONFIG_IDF_TARGET_ESP32)
#pragma message "当前的开发板是 ESP32"
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
#define NUM_LEDS 11
#define LED_PIN 1
#define BOARD_VISION 4
#include "lib/LED/WS2812_FastLed.h"
SoftwareSerial SoftSerialNFC(1, 2); // RX, TX

#elif defined(AIR001xx)
#pragma message "当前的开发板是 AIR001"
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
//LED灯的个数
#define NUM_LEDS  11
//LED引脚为PA7，不支持更改，不需要定义
#define BOARD_VISION 5
#include "lib/LED/WS2812_Air001.h"
HardwareSerial SerialPN532(PF0, PF1);
#define SerialNFC SerialPN532

#elif defined(_BOARD_GENERIC_STM32F103C_H_)
#define CDC
//for f103c8/B
#define EEPROM_PAGE_SIZE        (uint16)0x400  /* Page size = 1KByte */
#pragma message "当前的开发板是 STM32F103C8"
#define FLASH_SIZE 64

//for f103c6
//#pragma message "当前的开发板是 STM32F103C6"
// #define EEPROM_PAGE_SIZE        (uint16)0x200  /* Page size = 1KByte */
// #define FLASH_SIZE 32

#define EEPROM_START_ADDRESS    ((uint32)(0x8000000 + FLASH_SIZE * 1024 - 2 * EEPROM_PAGE_SIZE))
#define EEPROM_PAGE0_BASE               ((uint32)(EEPROM_START_ADDRESS + 0x000))
#define EEPROM_PAGE1_BASE               ((uint32)(EEPROM_START_ADDRESS + EEPROM_PAGE_SIZE))
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
#define BOARD_VISION 6

// #define LED_PIN_RED PB11
// #define LED_PIN_GREEN PB10
// #define LED_PIN_BLUE PB1
// #include "lib/LED/LED_analogwrite.h"
//旧版使用共阳LED

#define NUM_LEDS 11
#include "lib/LED/WS2812_STM32F1.h"
//新版使用WS2812
#define SerialNFC Serial1

#elif defined(ARDUINO_GENERIC_F072C8TX)
#define CDC
#pragma message "当前的开发板是 STM32F072C8"
//Generic STM32F1 series
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
#define BOARD_VISION 7

// #define LED_PIN_RED PB_11
// #define LED_PIN_GREEN PB_10
// #define LED_PIN_BLUE PB_1
// #include "lib/LED/LED_analogwrite.h"
//旧版使用共阳rgbLED

#define LED_PIN PA_7
#include "lib/LED/WS2812_NeoPixel.h"
//#include "lib/LED/WS2812_FastLed.h"
//新版使用WS2812

#define SerialNFC Serial1
HardwareSerial Serial1(PB_7, PB_6);

#elif defined(ARDUINO_ARCH_RP2040)
#define CDC
#pragma message "当前的开发板是 RP2040"
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
#define BOARD_VISION 8
//#define LED_PIN D5
#define SerialNFC Serial1

//#elif defined(__AVR_ATmega328P__)
//#pragma message "当前的开发板是 ATmega328P"
//#define SerialDevice Serial
//#define NUM_LEDS 11
//#define LED_PIN 13
//#define BOARD_VISION 9
//#include "lib/WS2812_FastLed.h"

#elif defined(CONFIG_IDF_TARGET_ESP32C3)
#define CDC 1
#pragma message "当前的开发板是 ESP32C3"
#define SerialDevice Serial
#define sysled 2
#define nfccommled 3
#define beeperpin 6
#define NUM_LEDS 11
#define LED_PIN 10
#define BOARD_VISION 10
#define SerialNFC Serial0
#include "lib/LED/WS2812_FastLed.h"

#elif defined(__AVR_ATtiny85__)
#pragma message "当前的开发板是 ATtiny85"
#define SerialDevice Serial
#define SPICEAPI_INTERFACE Serial
#define NUM_LEDS 11
#define LED_PIN 0
#define BOARD_VISION 11
#include "lib/LED/WS2812_NeoPixel.h"
#include <TinyPinChange.h>
#include <SoftSerial.h>
SoftSerial SoftSerialNFC(2, 1,false); // RX, TX

#else
#error "未经测试的开发板，请检查串口和针脚定义"

#endif

#if defined(SerialNFC)
#pragma message "使用 UART 连接 PN532"
#include <PN532_HSU.h>
PN532_HSU pn532(SerialNFC);
#else
#pragma message "使用 SWUART 连接 PN532"
#if defined(__AVR_ATtiny85__)
#include <PN532_SWHSU_Tiny85.h>
#else
#include <PN532_SWHSU.h>
#endif
PN532_SWHSU pn532(SoftSerialNFC);
#define SerialNFC SoftSerialNFC
#endif

#include "PN532.h"
PN532 nfc(pn532);

#if defined(ARDUINO_SAMD_ZERO)
#include <FlashAsEEPROM.h>
#else
#include <EEPROM.h>
#endif
//EEPROM
//1：系统设置，第0位保留，第1位是否开启高波特率，第二位是否开启LED，第三位是否启用AIC卡号映射，第四位是否开启扩展读卡,第五位SPICE模式是否使用真实卡号
//第六位表示SPICE模式是否使用2P刷卡
//读卡兼容：在sega与spice模式下增加对nesica(mifare ultralight)的支持(暂定，后续可能会增加其他卡片的支持)
//SPICE模式下默认使用UID作为卡号，如果开启了使用真实卡号，将尝试传入aime卡的真实卡号。部分版本SPICE可能会报错，不接受卡号
//2：LED亮度
//3：固件版本号
//4-11：被映射AIC卡号IDM
//12-22：目标卡号
//23:当前使用的系统模式：0为SEGA模式，1为SpiceTool模式，2为Namco模式，3为Test模式，4为RAW直通模式
uint8_t system_setting[3] = {0};
uint8_t mapped_card_IDm[8] = {0};
const uint8_t default_system_setting[3] = {0b00000100,128,10};
extern uint8_t system_mode;

void EEPROM_get_sysconfig(){
  #if defined(ESP8266)
  EEPROM.begin(32);
  #elif defined(ESP32)
  EEPROM.begin(32);
  #elif defined(_BOARD_GENERIC_STM32F103C_H_)
  EEPROM.init(EEPROM_PAGE0_BASE,EEPROM_PAGE1_BASE,EEPROM_PAGE_SIZE);
  #endif
  for(uint8_t i = 0;i<3;i++){
    system_setting[i] = EEPROM.read(i);
  }
  if(system_setting[2] != default_system_setting[2]){//固件版本号不同，刷入默认设置
    for(uint8_t i = 0;i<3;i++)  {
    EEPROM.write(i, default_system_setting[i]);
    system_setting[i] = default_system_setting[i];
    }
    EEPROM.write(23, 0);
    system_mode = 0;
  }else{
    system_mode = EEPROM.read(23);
    if(system_mode>4){
      system_mode = 0;
      EEPROM.write(23,0);
    }
  }
  #if defined(ESP8266)
  EEPROM.commit();
  #elif defined(ESP32)
  EEPROM.commit();
  #endif
}